Your contact: Therese McCarthy021 835 921Email my brief

Boot and hand hygiene at production entries

Start with what has to happen at the door.

Tell us the hygiene controls this entry needs: how boots are cleaned, how hands are washed and sanitised, and whether entry is enforced. The lane builds as you answer. Then we match the NZ Brush stations that deliver it.

Start from a typical entry:
Deluxe boot cleaner with green brushes
Boot brush
Stainless double hose and brush bay
Manual wash bay
Automated sole and upper wash
Automated boot wash
Gated automatic boot and hand wash channel
Gated hygiene entry

SimpleFully controlled

1

The entry

Where it is, who uses it, and how busy it gets.

 
What kind of entry is it?
What footwear goes through?
2

Boot controls

Dry areas usually need brushing only. Wet and high-care areas usually need washing and disinfectant.

Undersoles
Uppers and sides
Also needed
3

Hand controls

Tick every step your hygiene procedure asks for at this entry.

4

How sure do you need to be?

How certain you need to be that every person does every step, every time.

Enforcement
5

Site services

What is at the spot where the station would go. Not sure is fine: we check at the survey.

Power
Water
Floor waste or drain
6

Drivers and contact

What is behind the project, and who we should talk to.

What does this entry have to satisfy?
When do you need it working?
Budget for this entry (excl. GST)
Email the brief to Therese or compare the options first

Matched to your answers

Solutions for this entry

Each option is scored against the controls you chose and checked against your power, water, drainage and space. Add the ones you like to your brief.

$ under $1k$$ $1k to $3k$$$ $3k to $10k$$$$ $10k to $20k$$$$$ over $20kIndicative equipment cost, excl. GST, before installation.

The range

From a boot brush to a fully gated entry

Six levels of control. Each card shows what the station does, what it needs on site, and how much of your entry it covers on its own.

Around the entry

Support

Storage and spares that keep the entry working.

80365 · 80366

Stainless boot racks

304 stainless, 1750 mm high. 80365 holds 40 pairs (2000 mm wide); 80366 holds 20 pairs (1200 mm wide). Work boots stay on the clean side.

Made to order

Replacement rollers and brushes

We make boot-wash rollers and brushes to order in our New Zealand factory, so a worn roller does not mean waiting on an overseas part.

80390 to 80397

Station spares

Rollers, solenoid pumps, filters, handheld brushes and switches are NZ Brush stock lines for the stations we supply.

Send it to us

Your requirements brief

This is everything you entered, with the options you shortlisted. Send it to Therese and we will book a site survey to confirm services and space before we quote.


      

        
Therese McCarthyHygiene Accounts Manager, NZ Brush

        
therese@nzbrush.co.nz

        

          Email the brief
          
          
        

        

        
If the email button does not open your mail app, copy the brief and paste it into an email to the address above. Nothing is sent automatically, and your answers stay in this browser until you send them.

        
Phone Therese on 021 835 921 or call 0800 692 787.

      

    

  






  

    
How we work
Requirements first, then the station

    

      
Survey
We walk the entry with you
We check traffic at shift change, footwear, power, water, drainage and space before recommending anything.

      
Recommend
Matched to your procedure
Your hygiene SOP decides the steps. We match stations to it, from a single brush to a gated entry.

      
Install
Delivered and commissioned
We deliver, set up and commission the station with your team. Electrical and plumbing connections are made by registered trades.

      
Support
Spares and service in New Zealand
Rollers and brushes made in our own factory, and a service team on the road every week.

    

  







OptionsEmail brief